VMSTAT(1) NetBSD General Commands Manual VMSTAT(1)
vmstat -- report virtual memory statistics
vmstat [-CefHiLlmstUvW] [-c count] [-h hashname] [-M core] [-N system] [-u histname] [-w wait] [disks]
vmstat reports certain kernel statistics kept about process, virtual mem- ory, disk, trap, and CPU activity. The options are as follows: -C Report on kernel memory caches. Combine with the -m option to see information about memory pools that back the caches. -c count Repeat the display count times. The first display is for the time since a reboot and each subsequent report is for the time period since the last display. If no wait interval is specified, the default is 1 second. -e Report the values of system event counters. -f Report fork statistics. -H Report all hash table statistics. -h hashname Report hash table statistics for hashname. -i Report the values of system interrupt counters. -L List all the hashes supported for -h and -H. -l List the UVM histories being maintained by the kernel. -M core Extract values associated with the name list from the speci- fied core instead of the default /dev/mem. -m Report on the usage of kernel dynamic memory listed first by size of allocation and then by type of usage, followed by a list of the kernel memory pools and their usage. -N system Extract the name list from the specified system instead of the default /netbsd. -s Display the contents of the uvmexp structure. This contains various paging event and memory status counters. -t Display the contents of the vmtotal structure. This includes information about processes and virtual memory. The process part shows the number of processes in the fol- lowing states: ru on the run queue dw in disk I/O wait pw waiting for paging sl sleeping while resident sw swapped out, but either runnable or in short-term blocking state The virtual memory section shows: total-v Total virtual memory active-v Active virtual memory in use active-r Active real memory in use vm-sh Shared virtual memory avm-sh Active shared virtual memory rm-sh Shared real memory arm-sh Active shared real memory free Free memory All memory values are shown in number of pages. -U Dump all UVM histories. -u histname Dump the specified UVM history. -v Print more verbose information. When used with the -i, -e, or -m options prints out all counters, not just those with non-zero values. -W Print more verbose information about kernel memory pools. -w wait Pause wait seconds between each display. If no repeat count is specified, the default is infinity. By default, vmstat displays the following information: procs Information about the numbers of processes in various states. r in run queue b blocked for resources (i/o, paging, etc.) w runnable or short sleeper (< 20 secs) but swapped memory Information about the usage of virtual and real memory. Virtual pages (reported in units of 1024 bytes) are considered active if they belong to processes which are running or have run in the last 20 seconds. avm active virtual pages fre size of the free list page Information about page faults and paging activity. These are averaged every five seconds, and given in units per second. flt total page faults re page reclaims (simulating reference bits) pi pages paged in po pages paged out fr pages freed per second sr pages scanned by clock algorithm, per-second disks Disk transfers per second. Typically paging will be split across the available drives. The header of the field is the first char- acter of the disk name and the unit number. If more than four disk drives are configured in the system, vmstat displays only the first four drives. To force vmstat to display specific drives, their names may be supplied on the command line. faults Trap/interrupt rate averages per second over last 5 seconds. in device interrupts per interval (including clock interrupts) sy system calls per interval cs CPU context switch rate (switches/interval) cpu Breakdown of percentage usage of CPU time. us user time for normal and low priority processes sy system time id CPU idle
/netbsd default kernel namelist /dev/mem default memory file
The command ``vmstat -w 5'' will print what the system is doing every five seconds; this is a good choice of printing interval since this is how often some of the statistics are sampled in the system. Others vary every second and running the output for a while will make it apparent which are recomputed every second.
fstat(1), netstat(1), nfsstat(1), ps(1), systat(1), iostat(8), pstat(8) The sections starting with ``Interpreting system activity'' in Installing and Operating 4.3BSD.
The -c and -w options are only available with the default output. The -l, -U, and -u options are useful only if the system was compiled with support for UVM history. NetBSD 5.1 November 6, 2007 NetBSD 5.1
You can also request any man page by name and (optionally) by section: