SYSLOGD(8) NetBSD System Manager's Manual SYSLOGD(8)
syslogd -- log systems messages
syslogd [-dnrSsTUvX] [-B buffer_length] [-b bind_address] [-f config_file] [-g group] [-m mark_interval] [-o output_format] [-P file_list] [-p log_socket [-p log_socket2 ...]] [-t chroot_dir] [-u user]
syslogd reads and logs messages to the system console, log files, other machines and/or users as specified by its configuration file. The options are as follows: -B buffer_length Sets the receiving buffer length. The default is 16384 bytes. If syslogd reports buffer overflow, this needs increasing. If you don't care about it being reported, see the -X option. -b bind_address Specify one specific IP address or hostname to bind to. If a hostname is specified, the IPv4 or IPv6 address which corresponds to it is used. -d Enable debugging to the standard output, and do not dis- associate from the controlling terminal. -f config_file Specify the pathname of an alternative configuration file; the default is /etc/syslog.conf. -g group Set GID to group after the sockets and log files have been opened. -m mark_interval Select the number of minutes between ``mark'' messages; the default is 20 minutes. -n Do not perform hostname lookups; report only numeric addresses. -o output_format Select output message format. bsd, rfc3164 traditional BSD Syslog format (default) syslog, rfc5424 new syslog-protocol format -P Specify the pathname of a file containing a list of sockets to be created. The format of the file is simply one socket per line. -p log_socket Specify the pathname of a log socket. Multiple -p options create multiple log sockets. If no -p arguments are given, the default socket of /var/run/log is used. -r Disable the compression of repeated instances of the same line into a single line of the form ``last message repeated N times''. -S Sync kernel messages to disk immediately. -s Select ``secure'' mode, in which syslogd does not listen on a UDP socket but only communicates over a UNIX domain socket. This is valuable when the machine on which syslogd runs is subject to attack over the network and it is desired that the machine be protected from attempts to remotely fill logs and similar attacks. -T Always use the local time and date for messages received from the network, instead of the timestamp field sup- plied in the message by the remote host. This is useful if some of the originating hosts can't keep time prop- erly or are unable to generate a correct timestamp. -t chroot_dir chroot(2) to chroot_dir after the sockets and log files have been opened. -U Unique priority logging. Only log messages at the pri- ority specified by the selector in the configuration file. Without this option, messages at the specified priority or higher are logged. This option changes the default priority comparison from `>=' to `='. -u user Set UID to user after the sockets and log files have been opened. -v Verbose logging. If specified once, the numeric facil- ity and priority are logged with each locally-written message. If specified more than once, the names of the facility and priority are logged with each locally-writ- ten message. -X Disable logging of buffer overflow. syslogd reads its configuration file when it starts up and whenever it receives a hangup signal. For information on the format of the configu- ration file, see syslog.conf(5). syslogd reads messages from the UNIX domain socket /var/run/log, from an Internet domain socket specified in /etc/services, and from the special device /dev/klog (to read kernel messages). syslogd creates the file /var/run/syslogd.pid, and stores its process id there. This can be used to kill or reconfigure syslogd. By using multiple -p options, one can set up many chroot environments by passing the pathname to the log socket (/var/run/log) in each chroot area to syslogd. For example: syslogd -p /var/run/log -p /web/var/run/log -p /ftp/var/run/log Note: the normal log socket must now also be passed to syslogd. The logged message includes the date, time, and hostname (or pathname of the log socket). Commonly, the program name and the process id is included. The date and time are taken from the received message. If the format of the timestamp field is incorrect, time obtained from the local host is used instead. This can be overridden by the -T flag. Accesses from UDP socket can be filtered by libwrap configuration files, like /etc/hosts.deny. Specify ``syslogd'' in daemon_list portion of the configuration files. Refer to hosts_access(5) for details. SYSLOG PROTOCOL NOTES syslogd accepts messages in traditional BSD Syslog or in newer Syslog Protocol format. See RFC 3164 (BSD Syslog) and RFC 5424 (Syslog Proto- col) for detailed description of the message format. Messages from the local kernel that are not tagged with a priority code receive the default facility LOG_KERN and priority LOG_NOTICE. All other untagged messages receive the default facility LOG_USER and priority LOG_NOTICE.
/etc/syslog.conf The configuration file. /var/run/syslogd.pid The process id of current syslogd. /var/run/log Name of the UNIX domain datagram log socket. /dev/klog The kernel log device.
logger(1), syslog(3), services(5), syslog.conf(5), newsyslog(8) The BSD syslog Protocol, RFC, 3164, August 2001. The Syslog Protocol, RFC, 5424, March 2009.
The syslogd command appeared in 4.3BSD. Support for multiple log sockets appeared in NetBSD 1.4. libwrap support appeared in NetBSD 1.6. Support for RFC 5424, TLS encryption and authentication, signed messages appeared in NetBSD 6.0. NetBSD 9.0 November 4, 2018 NetBSD 9.0
You can also request any man page by name and (optionally) by section: