SAVECORE(8)             NetBSD System Manager's Manual             SAVECORE(8)


NAME
savecore -- save a core dump of the operating system
SYNOPSIS
savecore [-fvz] [-N system] [-Z level] directory savecore -c [-v] [-N system] savecore -n [-v] [-N system]
DESCRIPTION
When the NetBSD kernel encounters a fatal error, the panic(9) routine arranges for a snapshot of the contents of physical memory to be written into a dump area, typically in the swap partition. Upon a subsequent reboot, savecore is typically run out of rc(8), before swapping is enabled, to copy the kernel and the saved memory image into directory, and enters a reboot message and information about the core dump into the system log. The kernel and core file can then be analyzed using various tools, including dmesg(8), fstat(1), gdb(1), iostat(8), netstat(1), ps(1), and pstat(8), to attempt to deduce the cause of the crash. Crashes are usually the result of kernel bugs; if this is suspected, a full bug report should be filed using send-pr(1), containing as much information as possible about the circumstances of the crash. Since crash dumps are typically very large and may contain whatever (poten- tially confidential) information was in memory at the time of the crash, do NOT include a copy of the crash dump file in the bug report; instead, save it somewhere in the event that a NetBSD developer wants to examine it. The options are as follows: -c Only clears the dump without saving it, so that future invoca- tions of savecore will ignore it. -f Forces a dump to be taken even if the dump doesn't appear cor- rect or there is insufficient disk space. -n Check whether a dump is present without taking further action. The command exits with zero status if a dump is present, or with non-zero status otherwise. -N Use system as the kernel instead of the default (returned by getbootfile(3)). Note that getbootfile(3) uses secure_path(3) to check that kernel file is ``secure'' and will default to /netbsd if the check fails. -v Prints out some additional debugging information. -z Compresses the core dump and kernel (see gzip(1)). -Z level Set the compression level for -z to level. Defaults to 1 (the fastest compression mode). Refer to gzip(1) for more informa- tion regarding the compression level. savecore checks the core dump in various ways to make sure that it is current and that it corresponds to the currently running system. If it passes these checks, it saves the core image in directory/netbsd.#.core and the system in directory/netbsd.# (or in directory/netbsd.#.core.gz and directory/netbsd.#.gz, respectively, if the -z option is used). The ``#'' is the number from the first line of the file directory/bounds, and it is incremented and stored back into the file each time savecore suc- cessfully runs. savecore also checks the available disk space before attempting to make the copies. If there is insufficient disk space in the file system con- taining directory, or if the file directory/minfree exists and the number of free kilobytes (for non-superusers) in the file system after the copies were made would be less than the number in the first line of this file, the copies are not attempted. If savecore successfully copies the kernel and the core dump, the core dump is cleared so that future invocations of savecore will ignore it.
SEE ALSO
fstat(1), gdb(1), gzip(1), netstat(1), ps(1), send-pr(1), secure_path(3), dmesg(8), iostat(8), pstat(8), rc(8), syslogd(8), panic(9)
HISTORY
The savecore command appeared in 4.1BSD.
BUGS
The minfree code does not consider the effect of compression. NetBSD 5.0_RC4 October 16, 2004 NetBSD 5.0_RC4

You can also request any man page by name and (optionally) by section:

Command: 
Section: 
Architecture: 
Collection: 
 

Use the DEFAULT collection to view manual pages for third-party software.


Powered by man-cgi 1.15, Panagiotis Christias
Modified for NetBSD by Kimmo Suominen