NDP(8)                  NetBSD System Manager's Manual                  NDP(8)

NAME
     ndp -- control/diagnose IPv6 neighbor discovery protocol

SYNOPSIS
     ndp [-nt] hostname
     ndp [-nt] -a | -c | -p
     ndp [-nt] -r
     ndp [-nt] -H | -P | -R
     ndp [-nt] -A wait
     ndp [-nt] -d hostname
     ndp [-nt] -f filename
     ndp [-nt] -i interface [expressions ...]
     ndp [-nt] -I [interface | delete]
     ndp [-nt] -s nodename etheraddr [temp] [proxy]

DESCRIPTION
     The ndp command manipulates the address mapping table used by the Neigh-
     bor Discovery Protocol (NDP).

     -a      Dump the currently existing NDP entries.  The following informa-
             tion will be printed:

             Neighbor    IPv6 address of the neighbor.

             Linklayer Address
                         Linklayer address of the neighbor.  It could be
                         ``(incomplete)'' when the address is not available.

             Netif       Network interface associated with the neighbor cache
                         entry.

             Expire      The time until expiry of the entry.  The entry could
                         become ``permanent'', in which case it will never
                         expire.

             S           State of the neighbor cache entry, as a single let-
                         ter:

                         N       Nostate
                         W       Waitdelete
                         I       Incomplete
                         R       Reachable
                         S       Stale
                         D       Delay
                         P       Probe
                         ?       Unknown state (should never happen).

             Flags       Flags on the neighbor cache entry, in a single let-
                         ter.  They are: Router, proxy neighbor advertisement
                         (``p'').  The field could be followed by a decimal
                         number, which means the number of NS probes the node
                         has sent during the current state.

     -A wait
             Repeat -a (dump NDP entries) every wait seconds.

     -c      Erase all the NDP entries.

     -d      Delete specified NDP entry.

     -f      Parse the file specified by filename.

     -H      Harmonize consistency between the routing table and the default
             router list; install the top entry of the list into the kernel
             routing table.

     -I      Shows the default interface used as the default route when there
             is no default router.

     -I interface
             Specifies the default interface to be used when there is no
             interface specified even though required.

     -I delete
             The current default interface will be deleted from the kernel.

     -i interface [expressions ...]
             View ND information for the specified interface.  If additional
             arguments expressions are given, ndp sets or clears the flags or
             variables for the interface as specified in the expression.  Each
             expression should be separated by white spaces or tab characters.
             Possible expressions are as follows.  Some of the expressions can
             begin with the special character `-', which means the flag speci-
             fied in the expression should be cleared.  Note that you need --
             before -foo in this case.

             nud     Turn on or off NUD (Neighbor Unreachability Detection) on
                     the interface.  NUD is usually turned on by default.
             accept_rtadv
                     Specify whether or not to accept Router Advertisement
                     messages received on the interface.  Note that the kernel
                     does not accept Router Advertisement messages unless the
                     net.inet6.ip6.accept_rtadv variable is non-0, even if the
                     flag is on.  This flag is set to 1 by default.
             prefer_source
                     Prefer addresses on the interface as candidates of the
                     source address for outgoing packets.  The default value
                     of this flag is off.  For more details about the entire
                     algorithm of source address selection, see the
                     IMPLEMENTATION file supplied with the KAME kit.
             disabled
                     Disable IPv6 operation on the interface.  When disabled,
                     the interface discards any IPv6 packets received on or
                     being sent to the interface.  In the sending case, an
                     error of ENETDOWN will be returned to the application.
                     This flag is typically set automatically in the kernel as
                     a result of a certain failure of Duplicate Address Detec-
                     tion.  While the flag can be set or cleared by hand with
                     the ndp command, it is not generally advisable to modify
                     this flag manually.
             basereachable=(number)
                     Specify the BaseReachbleTimer on the interface in mil-
                     lisecond.
             retrans=(number)
                     Specify the RetransTimer on the interface in millisecond.
             curhlim=(number)
                     Specify the Cur Hop Limit on the interface.

     -n      Do not try to resolve numeric addresses to hostnames.

     -p      Show prefix list.

     -P      Flush all the entries in the prefix list.

     -r      Show default router list.

     -R      Flush all the entries in the default router list.

     -s      Register an NDP entry for a node.  The entry will be permanent
             unless the word temp is given in the command.  If the word proxy
             is given, this system will act as a proxy NDP server, responding
             to requests for hostname even though the host address is not its
             own.

     -t      Print timestamp on each entry, making it possible to merge output
             with tcpdump(8).  Most useful when used with -A.

RETURN VALUES
     The ndp command will exit with 0 on success, and non-zero on errors.

SEE ALSO
     arp(8)

HISTORY
     The ndp command first appeared in the WIDE Hydrangea IPv6 protocol stack
     kit.

NetBSD 5.1                       March 5, 2006                      NetBSD 5.1

You can also request any man page by name and (optionally) by section:

Command: 
Section: 
Architecture: 
Collection: 
 

Use the DEFAULT collection to view manual pages for third-party software.


©1994 Man-cgi 1.15, Panagiotis Christias <christia@softlab.ntua.gr>
©1996-2014 Modified for NetBSD by Kimmo Suominen