IWN(4)                  NetBSD Kernel Interfaces Manual                 IWN(4)

NAME
     iwn -- Intel Wireless 4965AGN IEEE 802.11 driver

SYNOPSIS
     iwn* at pci? dev ? function ?

DESCRIPTION
     The iwn driver provides support for Intel Wireless WiFi Link 4965AGN Mini
     PCI Express network adapters.

     By default, the iwn driver configures the adapter for BSS operation (aka
     infrastructure mode).  This mode requires the use of an access point.

     For more information on configuring this device, see ifconfig(8).

CONFIGURATION
     The iwn driver can be configured at runtime with ifconfig(8) using the
     following parameters:

     bssid bssid
             Set the desired BSSID.

     -bssid  Unset the desired BSSID.  The interface will automatically select
             a BSSID in this mode, which is the default.

     chan n  Set the channel (radio frequency) to be used by the driver based
             on the given channel ID n.

     -chan   Unset the desired channel to be used by the driver.  The driver
             will automatically select a channel in this mode, which is the
             default.

     media media
             The iwn driver supports the following media types:

             autoselect  Enable autoselection of the media type and options.

     mediaopt opts
             The iwn driver supports the following media options:

             monitor  Select monitor mode.

     -mediaopt opts
             Disable the specified media options on the driver and return it
             to the default mode of operation (BSS).

     mode mode
             The iwn driver supports the following modes:

             11a  Force 802.11a operation.
             11b  Force 802.11b operation.
             11g  Force 802.11g operation.

     nwid id
             Set the network ID.  The id can either be any text string up to
             32 characters in length, or a series of hexadecimal digits up to
             64 digits.  An empty id string allows the interface to connect to
             any available access points.  By default the iwn driver uses an
             empty string.  Note that network ID is synonymous with Extended
             Service Set ID (ESSID).

     nwkey key
             Enable WEP encryption using the specified key.  The key can
             either be a string, a series of hexadecimal digits (preceded by
             `0x'), or a set of keys of the form ``n:k1,k2,k3,k4'', where `n'
             specifies which of the keys will be used for transmitted packets,
             and the four keys, ``k1'' through ``k4'', are configured as WEP
             keys.  If a set of keys is specified, a comma (`,') within the
             key must be escaped with a backslash.  Note that if multiple keys
             are used, their order must be the same within the network.  iwn
             is capable of using both 40-bit (5 characters or 10 hexadecimal
             digits) or 104-bit (13 characters or 26 hexadecimal digits) keys.

     -nwkey  Disable WEP encryption.  This is the default mode of operation.

EXAMPLES
     The following example configures iwn0 to join whatever network is avail-
     able on boot, using WEP key ``0x1deadbeef1'', channel 11, obtaining an IP
     address using DHCP:

           dhcp NONE NONE NONE nwkey 0x1deadbeef1 chan 11

     Configure iwn0 for WEP, using hex key ``0x1deadbeef1'':

           # ifconfig iwn0 nwkey 0x1deadbeef1

     Return iwn0 to its default settings:

           # ifconfig iwn0 -bssid -chan media autoselect \
                   nwid "" -nwkey

     Join an existing BSS network, ``my_net'':

           # ifconfig iwn0 192.168.1.1 netmask 0xffffff00 nwid my_net

DIAGNOSTICS
     iwn%d: device timeout  A frame dispatched to the hardware for transmis-
     sion did not complete in time.  The driver will reset the hardware.  This
     should not happen.

     iwn%d: fatal firmware error  For some reason, the firmware crashed.  The
     driver will reset the hardware.  This should not happen.

     iwn%d: radio is disabled by hardware switch  The radio transmitter is off
     and thus no packet can go out.  The driver will reset the hardware.  Make
     sure the laptop radio switch is on.

     iwn%d: error %d, could not read firmware %s  For some reason, the driver
     was unable to read the firmware image from the filesystem.  The file
     might be missing or corrupted.

     iwn%d: firmware file too short: %d bytes  The firmware image is corrupted
     and can't be loaded into the adapter.

     iwn%d: could not load firmware  An attempt to load the firmware into the
     adapter failed.  The driver will reset the hardware.

SEE ALSO
     arp(4), ifmedia(4), intro(4), netintro(4), pci(4), ifconfig(8)

     The IWN Web Page, http://damien.bergamini.free.fr/iwn/.

AUTHORS
     The iwn driver and this man page were written by Damien Bergamini
     <damien.bergamini@free.fr>.

NetBSD 5.0_RC4                 November 7, 2008                 NetBSD 5.0_RC4

You can also request any man page by name and (optionally) by section:

Command: 
Section: 
Architecture: 
Collection: 
 

Use the DEFAULT collection to view manual pages for third-party software.


©1994 Man-cgi 1.15, Panagiotis Christias <christia@softlab.ntua.gr>
©1996-2014 Modified for NetBSD by Kimmo Suominen