CCDCONFIG(8)            NetBSD System Manager's Manual            CCDCONFIG(8)

     ccdconfig -- configuration utility for the concatenated disk driver

     ccdconfig [-cv] ccd ileave [flags] dev [...]
     ccdconfig -C [-v] [-f config_file]
     ccdconfig -u [-v] ccd [...]
     ccdconfig -U [-v] [-f config_file]
     ccdconfig -g [ccd [...]]

     ccdconfig is used to dynamically configure and unconfigure concatenated
     disk devices, or ccds.  For more information about the ccd, see ccd(4).

     The options are as follows:

     -c      Configure a ccd.  This is the default behavior of ccdconfig.

     -C      Configure all ccd devices listed in the ccd configuration file.

     -f config_file
             When configuring or unconfiguring all devices, read the file
             config_file instead of the default /etc/ccd.conf.

     -g      Dump the current ccd configuration in a format suitable for use
             as the ccd configuration file.  If no arguments are specified,
             every configured ccd is dumped.  Otherwise, the configuration of
             each listed ccd is dumped.

     -u      Unconfigure a ccd.

     -U      Unconfigure all ccd devices listed the ccd configuration file.

     -v      Causes ccdconfig to be verbose.

     A ccd is described on the command line and in the ccd configuration file
     by the name of the ccd, the interleave factor, the ccd configuration
     flags, and a list of one or more devices.  The flags may be represented
     as a decimal number, a hexadecimal number, a comma-separated list of
     strings, or the word ``none''.  The flags are as follows:

           Symbolic         Numeric  Comment
           CCDF_UNIFORM     0x02     Use uniform interleave. The size of all
                                     components is clamped to that of the
                                     smallest component.
           CCDF_NOLABEL     0x04     Ignore raw disklabel. Useful when creat-
                                     ing a new ccd.

     The file /etc/ccd.conf is used to configure ccdconfig if -C or -U is
     used.  Each line of the configuration file contains arguments as per the
     -c argument: ccd ileave [flags] dev [...]

     A `#' is a comment, and everything to end of line is ignored.  A `\' at
     the end of a line indicates that the next line should be concatenated
     with the current.  A `\' preceding any character (other than the end of
     line) prevents that character's special meaning from taking effect.

     See EXAMPLES for an example of /etc/ccd.conf.

     /etc/ccd.conf - default ccd configuration file.

     The following command, executed from the command line, would configure
     ccd0 with 4 components (/dev/sd2e, /dev/sd3e, /dev/sd4e, /dev/sd5e), and
     an interleave factor of 32 blocks.

           # ccdconfig ccd0 32 0 /dev/sd2e /dev/sd3e /dev/sd4e /dev/sd5e

     An example /etc/ccd.conf:

           # /etc/ccd.conf
           # Configuration file for concatenated disk devices

           # ccd           ileave  flags   component devices
           ccd0            16      none    /dev/sd2e /dev/sd3e

     ccd(4), ccd.conf(5), rc(8)

     The ccdconfig command first appeared in NetBSD 1.1.

NetBSD 7.1.2                   October 17, 2003                   NetBSD 7.1.2

You can also request any man page by name and (optionally) by section:


Use the DEFAULT collection to view manual pages for third-party software.

©1994 Man-cgi 1.15, Panagiotis Christias
©1996-2019 Modified for NetBSD by Kimmo Suominen