TUNEFS(8)               NetBSD System Manager's Manual               TUNEFS(8)

NAME
     tunefs - tune up an existing file system

SYNOPSIS
     tunefs [-AFN] [-a maxcontig] [-d rotdelay] [-e maxbpg] [-g avgfilesize]
            [-h avgfpdir] [-k trackskew] [-m minfree] [-o optimize_preference]
            special | filesys

DESCRIPTION
     tunefs is designed to change the dynamic parameters of a file system
     which affect the layout policies.

     The following options are supported by tunefs:

     -A      Cause the values to be updated in all the alternate superblocks
             instead of just the standard superblock.  If this option is not
             used, then use of a backup superblock by fsck(8) will lose any-
             thing changed by tunefs.  -A is ignored when -N is specified.

     -F      Indicates that special is a file system image, rather than a de-
             vice name or file system mount point.  special will be accessed
             `as-is'.

     -N      Display all the settable options (after any changes from the tun-
             ing options) but do not cause any of them to be changed.

     -a maxcontig
             This specifies the maximum number of contiguous blocks that will
             be laid out before forcing a rotational delay (see -d below).
             The default value is one, since most device drivers require an
             interrupt per disk transfer.  Device drivers that can chain sev-
             eral buffers together in a single transfer should set this to the
             maximum chain length.

     -d rotdelay
             This specifies the expected time (in milliseconds) to service a
             transfer completion interrupt and initiate a new transfer on the
             same disk.  It is used to decide how much rotational spacing to
             place between successive blocks in a file.

     -e maxbpg
             This indicates the maximum number of blocks any single file can
             allocate out of a cylinder group before it is forced to begin al-
             locating blocks from another cylinder group.  Typically this val-
             ue is set to about one quarter of the total blocks in a cylinder
             group.  The intent is to prevent any single file from using up
             all the blocks in a single cylinder group, thus degrading access
             times for all files subsequently allocated in that cylinder
             group.  The effect of this limit is to cause big files to do long
             seeks more frequently than if they were allowed to allocate all
             the blocks in a cylinder group before seeking elsewhere.  For
             file systems with exclusively large files, this parameter should
             be set higher.

     -g avgfilesize
             This specifies the expected average file size.

     -h avgfpdir
             This specifies the expected number of files per directory.

     -k trackskew
             This specifies the skew in sectors from one track to the next in
             a cylinder.  The default value is zero, indicating that each
             track in a cylinder begins at the same rotational position.

     -m minfree
             This value specifies the percentage of space held back from nor-
             mal users; the minimum free space threshold.  The default value
             used is 10%.  This value can be set to zero, however up to a fac-
             tor of three in throughput will be lost over the performance ob-
             tained at a 10% threshold.  Note that if the value is raised
             above the current usage level, users will be unable to allocate
             files until enough files have been deleted to get under the high-
             er threshold.

     -o optimize_preference
             The file system can either try to minimize the time spent allo-
             cating blocks, or it can attempt to minimize the space fragmenta-
             tion on the disk.  If the value of minfree (see above) is less
             than 10%, then the file system should optimize for space to avoid
             running out of full sized blocks.  For values of minfree greater
             than or equal to 10%, fragmentation is unlikely to be problemati-
             cal, and the file system can be optimized for time.

             optimize_preference can be specified as either space or time.

SEE ALSO
     fs(5), dumpfs(8), fsck_ffs(8), newfs(8)

     M. McKusick, W. Joy, S. Leffler, and R. Fabry, "A Fast File System for
     UNIX", ACM Transactions on Computer Systems 2, 3, pp 181-197, August
     1984, (reprinted in the BSD System Manager's Manual, SMM:5).

HISTORY
     The tunefs command appeared in 4.2BSD.

BUGS
     This program should work on mounted and active file systems.  Because the
     super-block is not kept in the buffer cache, the changes will only take
     effect if the program is run on unmounted file systems.  To change the
     root file system, the system must be rebooted after the file system is
     tuned.

     You can tune a file system, but you can't tune a fish.

NetBSD 1.6                     November 9, 2001                              2

You can also request any man page by name and (optionally) by section:

Command: 
Section: 
Architecture: 
Collection: 
 

Use the DEFAULT collection to view manual pages for third-party software.


©1994 Man-cgi 1.15, Panagiotis Christias
©1996-2017 Modified for NetBSD by Kimmo Suominen